Read Chapter wise CCNA 3 Exam Answers (v5.1 + v6.0) CCNA 3 Chapter 9 Exam Answers 20201. What are two reasons for creating an OSPF network with multiple areas? (Choose two.)
2. What is used to facilitate hierarchical routing in OSPF?
3. A network administrator is verifying a multi-area OSPF configuration by checking the routing table on a router in area 1. The administrator notices a route to a network that is connected to a router in area 2. Which code appears in front of this route in the routing table within area 1? 4. Which two statements correctly describe OSPF type 3 LSAs? (Choose two.)
5. Which characteristic describes both ABRs and ASBRs that are implemented in a multiarea OSPF network?
6. What type of OSPF LSA is originated by ASBR routers to advertise external routes?
7. What OSPF LSA type is used to inform routers of the router ID of the DR in each multiaccess network in an OSPF area?
8. Refer to the exhibit. Which two statements are correct? (Choose two.)
9. What routing table descriptor is used to identify OSPF summary networks that originate from an ABR? 10. Refer to the exhibit. What can be concluded about network 192.168.4.0 in the R2 routing table?
11. Which three steps in the design and implementation of a multiarea OSPF network are considered planning steps?(Choose three.)
12. Which two networks are part of the summary route 192.168.32.0/22? (Choose two.)
13. Refer to the exhibit. What is indicated by the O IA in the router output?
14.Refer to the exhibit. A network administrator has been asked to summarize the networks shown in the exhibit as part of a multiarea OSPF implementation. All addresses are using a subnet mask of 255.255.255.0. What is the correct summarization for these eight networks?
15. The network administrator has been asked to summarize the routes for a new OSPF area. The networks to be summarized are 172.16.8.0, 172.16.10.0, and 172.16.12.0 with subnet masks of 255.255.255.0 for each network. Which command should the administrator use to forward the summary route for area 15 into area ?
16. Question as presented: 17. Fill in the blank. Do not use acronyms. Correct Answer: designated* 18. Fill in the blank. Use a number. An ASBR generates type ________ LSAs for each of its external routes and floods them into the area that it is connected to. Correct Answer: 5* 19. Fill in the blank. Use a number. A type ___________ LSA identifies the ASBR and provides a route to it. Correct Answer: 4* 20. Refer to the exhibit. Fill in the blank. Do not use abbreviations. The ____________ command must be issued to configure R1 for multiarea OSPF. Correct Answer: network 192.168.10.128 0.0.0.127 area 1* 21. Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
22. Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Fill in the blank. Do not use abbreviations. What is the missing command on router R2 to establish an adjacency between routers R1 and R3? Correct Answer: network 172.16.10.0 0.0.0.255 area 0* 23. Which IOS 12.4 software package integrates full features, including voice, security, and VPN capabilities, for all routing protocols?
24. What is the major release number in the IOS image name c1900-universalk9-mz.SPA.152-3.T.bin? 25. What statement describes a Cisco IOS image with the “universalk9_npe” designation for Cisco ISR G2 routers?
26. Which statement describes a difference between the IOS 15.0 extended maintenance release and a standard maintenance release?
27. When a router is powered on, where will the router first search for a valid IOS image to load by default?
28. A network engineer is upgrading the Cisco IOS image on a 2900 series ISR. What command could the engineer use to verify the total amount of flash memory as well as how much flash memory is currently available?
29. The customer of a networking company requires VPN connectivity for workers who must travel frequently. To support the VPN server, the customer router must be upgraded to a new Cisco IOS software version with the Advanced IP Services feature set. What should the field engineer do before copying the new IOS to the router?
30. A network administrator configures a router with the command sequence:
31. Beginning with the Cisco IOS Software Release 15.0, which license is a prerequisite for installing additional technology pack licenses? 32. Which three software packages are available for Cisco IOS Release 15.0?
33. When a customer purchases a Cisco IOS 15.0 software package, what serves as the receipt for that customer and is used to obtain the license as well?
34. Which command would a network engineer use to find the unique device identifier of a Cisco router?
35. A newly hired network engineer wants to use a 2911 router from storage. What command would the technician use to verify which IOS technology licenses have been activated on the router?
36. Which command is used to configure a one-time acceptance of the EULA for all Cisco IOS software packages and features?
37. How long is the evaluation license period for Cisco IOS Release 15.0 software packages?
38. What is the purpose of a T train release in Cisco IOS 15?
39. What code in the Cisco IOS 15 image filename c1900-universalk9-mz.SPA.153-3.M.bin indicates that the file is digitally signed by Cisco? 40. What statement describes a Cisco IOS image with the “universalk9_npe” designation for Cisco ISR G2 routers?
41. How long is the evaluation license period for Cisco IOS Release 15.0 software packages?
42. Fill in the blank. Do not use abbreviations. 43. Refer to the exhibit. Match the components of the IOS image name to their description. (Not all options are used.) Place the options in the following order: maintanence release and rebuild number -> M4 new feature release number -> 4 file extension -> bin major release number -> 15 |